機械加工在從事各機件加工過程中，必須按本規程實施。 Mechanical processing must be carried out according to this regulation in the process of machining various parts. 四、實施步驟 Four. Implementation steps 4.1 凡從事各種機械的操作人員，必須經過安全技術培訓，考試合格后，方可上崗作業。 4.1 all operators engaged in various kinds of machinery must undergo safety training, and after they pass the examination, they can go to work. 4.2 操作前 4.2 before operation 4.2.1 工作前按規定嚴格使用防護用品，扎好袖口，不準圍圍巾、戴手套，女工發辯應挽在帽子內。操作人員必須站在腳踏板上。 4.2.1 strictly use protective equipment according to the regulations before the work, bind the cuffs, do not wrap scarves and gloves. The operator must stand on the pedal. 4.2.2 應對各部位螺栓、行程限位，信號，安全防護（保險）裝置及機械傳動部分、電器部分，各潤滑點進行嚴格檢查，確定可靠后，方可啟動。 4.2.2 should be strictly checked for all parts of the bolt, travel limit, signal, safety protection (insurance) device, mechanical transmission part, electrical part, and all the lubricating points. After the determination is reliable, it can be started. 4.2.3 各類機床照明應用安全電壓、電壓不得大于36伏。 4.2.3 all types of machine tool lighting applications safety voltage and voltage should not exceed 36 volts. 4.3 操作中 In the 4.3 operation 4.3.1 工、夾、刀具及工件必須裝夾牢固。各類機床，開車后應先進行低速空轉，一切正常后，方可正式作業。 4.3.1 the work, clip, cutter and workpiece must be firmly clamped. All kinds of machine tools should be carried out at low speed and idling after driving. 4.3.2 機床道軌面上、工作臺上禁止放工具和其他東西。不準用手清除鐵屑，應使用專門工具清掃。 4.3.2 tools and other tools are not allowed on the track and surface of the machine. No iron scrap should be removed by hand. Special tools should be used for cleaning. 4.3.3 機床開動前要觀察周?chē)鷦?dòng)態，機床開動后，要站在安全位置上，以避開機床運動部位和鐵屑飛濺。 4.3.3 the machine must observe the surrounding dynamic before starting the machine. After the machine is started, it must be on the safe position to avoid the movement parts of the machine and the spatter of iron filings. 4.3.4 各類機床運轉中，不準調節變速機構或行程，不得用手觸摸傳動部分、運動中型線  流水槽模具 景觀石 檢查井鋼模具 保定通風管道 隔離墩模具 保定保潔公司的工件、刀具等在加工中的工作表面，不準在運轉中測量任何尺寸，禁止隔著機床傳動部分傳遞或拿取工具等物品。 4.3.4 all kinds of machine tools are not allowed to adjust the transmission mechanism or travel, no hand touch the transmission parts, movement of the workpiece, tool and other working surface in the processing, no measurement of any size in the operation, the transmission part of the machine tool is prohibited to pass or take tools and other products. 4.3.5 發現有異常響動時，應立即停車檢修，不得強行或帶病運轉，機床不準超負荷使用